征服同学人妇系列,h黄动漫蜜芽在线观看,极品丝袜乱系列全集大全目录 ,国产老头老太dh,正在播放国产水嫩美女叫,精品国产一区二区三区日日嗨,天堂а√在线地址,妈妈给我避孕套跟他做咨询,日日鲁鲁鲁夜夜爽爽狠狠视频97,大地资源网在线观看免费动漫 ,2023国精产品一二二线

I. Ball and screw of turning and milling compound center

1. Take care to prevent particles such as chips, dust and impurities from entering the auxiliary working area of the screw, which will cause damage to the screw.

2. The ball screw is a moving accessory. It must be fully lubricated to avoid damage to the ball screw due to oil loss and dry friction. When the machine uses large flow cooling, pay attention to increasing the frequency and flow of ball screw lubrication to avoid water rust on the screw.

3. Don't make the nut exceed the travel limit;

4. Strictly prevent collisions, which will cause the ball screw nut returning device to be damaged and affect the accuracy and noise.

Second, the servo motor of the turning and milling compound center

1. When equipped with a servo motor or variable frequency speed regulation, according to the alarm information (alarm number) of the servo driver or inverter, find out the cause of the alarm and the method of eliminating the alarm, or call and contact our company personnel;

2. The main motor (variable-frequency motor or two-speed motor) and the drive motor (stepper motor or servo motor) should be protected from moisture. If the motor enters the water, it will cause a short circuit between the motors and burn the motor. The servo motor should prevent collision. Cause the servo motor encoder to be damaged;

3. When the machine tool is not in use for a long time, the main power should be cut off, and the machine tool should be continuously operated for at least once every month for 2-3 hours

4. When using the inverter, after the AC power is cut off, before the indicator of the digital operator of the AC motor driver does not go out, it means that there is still high voltage inside the AC motor driver. It is very dangerous. Before proceeding;

3. Spindle of turning and milling compound machining center

1. When the temperature difference between the main shaft and the bushing is too large, it will easily cause the main shaft bearing to burn out. The oil cooler temperature must be set according to the winter and summer temperatures;

2. In order to ensure the long-term smooth running and service life of the main shaft, the user should warm up the machine to ensure the service life of the main shaft after handing over with the machine;

3. It is recommended to maintain the spindle running speed at the normal running speed (85% of the high speed of the spindle).

4. The daily maximum speed running time should not exceed 1/4 of the daily processing time;

5. The outer ring of the main shaft is blown, and the pressure standard is set at 1.2 kg per square centimeter to 1.5 kg per square centimeter;

6. At the normal running speed of the spindle, the continuous running time must not exceed 8 hours. Every eight hours of spindle operation, the spindle needs to be slowed down to low speed for 1 hour.

7. In the normal use of the spindle of the lathe and milling machine tool, the parts are guaranteed for 1 year and the bearing is guaranteed at 1600 / hr.

8. Be careful when blowing iron chips with an air gun when the spindle is not equipped with a knife / tool holder. Do not allow iron chip powder / water to enter the taper hole of the spindle, which may lead to poor spindle accuracy or damage;

It should be noted that when running the spindle daily, you must first determine whether the blow of the outer ring of the spindle is normal;

Although the turning and milling composite machining center has strong mechanical processing performance, reasonable maintenance can maintain its machining accuracy and efficiency. Irrational maintenance will reduce its service life sharply, and the importance of maintenance is self-evident. Now, if you are looking for a professional turning and milling compound processing manufacturer or a mechanical processing manufacturer, you are welcome to call Shenzhen Chengyu Precision Machinery. We have more than 20 years of experience in precision machining, and our products cover a wide range of industries. Machinable materials include machinery Common metal and non-metal materials in processing, and the company first passed the IATF16949 quality management certification in the automotive field, is the rare manufacturer in Shenzhen area with automotive parts processing qualifications, is your trusted partner.